SUPER MICRO Computer Computer Hardware SC512 User Manual

®
SUPER  
SC512 Chassis Series  
SC512-260B  
SC512F-600B  
SC512-200B  
SC512F-520(B)  
SC512F-410(B)  
SC512F-260(B)  
SC512L-260(B)  
SC512L-200B  
SC512F-600LB  
SC512F-520L(B)  
SC512L-260(B)-LCD  
SC512F-350B  
SC512C-260(B)  
SC512C-200(B)  
SC512F-280(B)  
USER’S MANUAL  
1.0b  
 
Preface  
Preface  
About This Manual  
This manual is written for professional system integrators and PC technicians. It  
provides information for the installation and use of the SC512 1U chassis. Installa-  
tion and maintenance should be performed by experienced technicians only.  
Supermicro’s SC512 1U chassis features a unique and highly-optimized design  
for dual-core Xeon platforms. The chassis is equipped with a 200, 260, 280. 350,  
410, 520 or 600 Watt high-efficiency power supply for superb power savings. High-  
performance fans provide ample optimized cooling for FB-DIMM memory modules  
in a 1U form factor.  
This document lists compatible parts available when this document was published.  
Always refer to the our Web site for updates on supported parts and configura-  
tions.  
iii  
 
SC512 Chassis Manual  
Manual Organization  
Chapter 1: Introduction  
The first chapter provides a checklist of the main components included with this  
chassis and describes the main features. This chapter also includes contact infor-  
mation.  
Chapter 2: System Safety  
This chapter lists warnings, precautions, and system safety. You should thoroughly  
familiarize yourself with this chapter for a general overview of safety precautions  
that should be followed before installing and servicing this chassis.  
Chapter 3: Chassis Components  
Refer to this chapter for details on this chassis model including the fans, bays,  
airflow shields, and other components.  
Chapter 4: System Interface  
Refer to this chapter for details on the system interface, which includes the functions  
and information provided by the control panel on the chassis as well as other LEDs  
located throughout the system.  
Chapter 5: Chassis Setup and Maintenance  
Follow the procedures given in this chapter when installing, removing, or  
reconfiguring your chassis.  
Chapter 6: Rack Installation  
Refer to this chapter for detailed information on chassis rack installation. You should  
follow the procedures given in this chapter when installing, removing or reconfiguring  
your chassis into a rack environment.  
Appendix A Cables, Screws, and Other Accessories  
Appendix B Power Supply Specifications  
iv  
 
Preface  
Table of Contents  
About This Manual.............................................................................................iii  
Manual Organization..........................................................................................iv  
Chapter 1 Introduction  
1-1  
1-2  
Overview ......................................................................................................... 1-1  
Chassis Features ............................................................................................ 1-2  
CPU................................................................................................................. 1-2  
I/O Expansion slots......................................................................................... 1-2  
Peripheral Drives............................................................................................. 1-2  
Dual Hard Drives............................................................................................. 1-2  
Contacting Supermicro.................................................................................... 1-3  
Returning Merchandise for Service................................................................. 1-4  
1-3  
1-4  
Chapter 2 System Safety  
2-1  
2-2  
2-3  
2-4  
2-5  
2-6  
Overview ......................................................................................................... 2-1  
Warnings and Precautions.............................................................................. 2-1  
Preparing for Setup......................................................................................... 2-1  
Electrical Safety Precautions .......................................................................... 2-1  
General Safety Precautions............................................................................ 2-3  
System Safety................................................................................................. 2-3  
Chapter 3 Chassis Components  
3-1  
3-2  
Overview ......................................................................................................... 3-1  
Components.................................................................................................... 3-1  
Chassis............................................................................................................ 3-1  
Fans ................................................................................................................ 3-1  
Blower ............................................................................................................. 3-1  
Mounting Rails ................................................................................................ 3-1  
Power Supply.................................................................................................. 3-2  
Air Shroud ....................................................................................................... 3-2  
Where to get Replacement Components........................................................ 3-2  
Chassis Model Options................................................................................... 3-2  
Identifying Fan and Blower-Cooled Chassis Models...................................... 3-2  
Model SC512 .................................................................................................. 3-4  
Model SC512C................................................................................................ 3-5  
Model SC512F ................................................................................................ 3-6  
Model SC512L................................................................................................. 3-9  
3-3  
3-4  
v
 
SC512 Chassis Manual  
Chapter 4 System Interface  
4-1  
4-2  
4-3  
Overview ......................................................................................................... 4-1  
Control Panel Buttons..................................................................................... 4-2  
Control Panel LEDs ........................................................................................ 4-2  
Chapter 5 Chassis Setup and Maintenance  
5-1  
5-2  
Overview ......................................................................................................... 5-1  
Installation Procedures.................................................................................... 5-1  
General Maintenance...................................................................................... 5-1  
Removing the Chassis Cover ......................................................................... 5-2  
Installing Hard Drives...................................................................................... 5-3  
Installing the Motherboard .............................................................................. 5-5  
Important Motherboard Installation Information .............................................. 5-5  
Standoffs ......................................................................................................... 5-6  
Installing the DVD or CD-ROM Drive ............................................................. 5-7  
Expansion Slot Setup...................................................................................... 5-8  
Installing the Air Shroud.................................................................................. 5-9  
Installation Complete..................................................................................... 5-10  
System Fans ..................................................................................................5-11  
System Fan Tray............................................................................................5-11  
System Fan Tray Replacement..................................................................... 5-12  
Power Supply ............................................................................................... 5-13  
Power Supply Failure.................................................................................... 5-13  
Replacing the Chassis LED Panel................................................................ 5-15  
5-3  
5-4  
5-5  
5-6  
5-7  
5-8  
5-9  
Chapter 6 Rack Installation  
6-1  
6-2  
6-3  
Overview ......................................................................................................... 6-1  
Unpacking the System.................................................................................... 6-1  
Preparing for Setup......................................................................................... 6-1  
Choosing a Setup Location............................................................................. 6-1  
Rack Precautions............................................................................................ 6-2  
General Server Precautions............................................................................ 6-2  
Rack Mounting Considerations....................................................................... 6-3  
Ambient Operating Temperature ................................................................ 6-3  
Reduced Airflow ......................................................................................... 6-3  
Mechanical Loading ................................................................................... 6-3  
Circuit Overloading..................................................................................... 6-3  
Reliable Ground ......................................................................................... 6-3  
Rack Mounting Instructions............................................................................. 6-4  
Identifying the Sections of the Rack Rails (Optional Item)............................. 6-4  
6-4  
vi  
 
Preface  
Installing the Inner Rail Extension .................................................................. 6-5  
Installing the Outer Rails to the Rack............................................................. 6-6  
Installing the Chassis into a Rack................................................................... 6-8  
Mid-Mount Telco Rack..................................................................................... 6-9  
Installing the Chassis into a Rack in Mid-Mount Position .............................. 6-9  
Appendix A Cables, Screws, and Other Accessories  
Appendix B Power Supply Specifications  
vii  
 
SC512 Chassis Manual  
Notes  
viii  
 
Chapter 1: Introduction  
Chapter 1  
Introduction  
1-1 Overview  
Supermicro’s SC512 1U chassis features a unique and highly-optimized design.  
The chassis is equipped with a high-efficiency power supply in a small form factor  
for optimized space efficiency.  
The following chart lists model numbers and features currently available at the  
time of printing. For additional information visit the Supermicro Web site at www.  
supermicro.com  
SC512 Chassis  
Model  
CPU  
HDD  
I/O Slots  
Power Supply  
SC512-200B  
200W (High-Efficiency)  
260W  
UP  
UP  
1x Fixed 3.5"  
1x Fixed 3.5"  
1x Fixed 3.5"  
1x Fixed 3.5"  
1x Fixed 3.5"  
2x Fixed 3.5"  
2x Fixed 3.5"  
1x Fixed 3.5"  
2x Fixed 3.5"  
2x Fixed 3.5"  
1x Fixed 3.5"  
1x Fixed 3.5"  
1x Fixed 3.5"  
1x Fixed 3.5"  
1x Fixed 3.5"  
FH  
FH  
FH  
FH  
FH  
FH  
FH  
FH  
FH  
FH  
FH  
FH  
FH  
FH  
FH  
SC512-260B  
SC512C-200(B)  
SC512C-260(B)  
SC512F-260(B)  
SC512L-200B  
SC512L-260(B)  
SC512L-260(B)-LCD  
SC512F-280(B)  
SC512F-350B  
SC512F-410(B)  
SC512F-520(B)  
SC512F-600B  
SC512F-520L(B)  
SC512F-600LB  
UP  
200W  
UP  
260W  
UP  
260W  
UP  
200W  
UP  
260W  
UP  
260W  
DP/UP  
DP/UP  
DP/UP  
DP/UP  
DP/UP  
DP/UP  
DP/UP  
280W (High-Efficiency)  
350W (Gold Level)  
410W DC  
520W (High-Efficiency)  
600W (Gold Level)  
520W (High-Efficiency)  
600W (Gold Level)  
Legend:  
DP = Dual Processor Support  
FF = Full-height, Full-length  
LP = Low-profile  
UP = Single Processor Support  
FH = Full-height, Half-length  
1-1  
 
SC512 Chassis Manual  
1-2 Chassis Features  
The SC512 1U high-performance chassis supports a wide range of features. See  
the Chassis Components section of this manual for a list of featues included in  
each of the SC512 models.  
CPU  
The SC512 chassis supports a DP and/or UP Xeon, Pentium D, P3/P4 processors.  
Please refer to the motherboard specifications pages on our web site for updates  
on supported processors.  
I/O Expansion slots  
Each version of the SC512 chassis includes one full I/O expansion slot  
Peripheral Drives  
Some SC512 chassis support peripheral dives such as a DVD-ROM, CD-ROM or  
floppy disk drive. These drives allow data to be installed or saved quickly.  
Dual Hard Drives  
Some SC512 chassis models support a second hard disk drive. For more details,  
check the Chassis Components section of this manual or the Supermicro Website  
1-2  
 
Chapter 1 Introduction  
1-3 Contacting Supermicro  
Headquarters  
Address:  
Super Micro Computer, Inc.  
980 Rock Ave.  
San Jose, CA 95131 U.S.A.  
Tel:  
+1 (408) 503-8000  
+1 (408) 503-8008  
Fax:  
Email:  
marketing@supermicro.com (General Information)  
support@supermicro.com (Technical Support)  
Web Site:  
Europe  
Address:  
Super Micro Computer B.V.  
Het Sterrenbeeld 28, 5215 ML  
's-Hertogenbosch, The Netherlands  
Tel:  
+31 (0) 73-6400390  
Fax:  
Email:  
+31 (0) 73-6416525  
sales@supermicro.nl (General Information)  
support@supermicro.nl (Technical Support)  
rma@supermicro.nl (Customer Support)  
Asia-Pacific  
Address:  
Super Micro Computer, Inc.  
4F, No. 232-1, Liancheng Rd.  
Chung-Ho 235, Taipei County  
Taiwan, R.O.C.  
Tel:  
+886-(2) 8226-3990  
+886-(2) 8226-3991  
Fax:  
Web Site:  
Technical Support:  
Email:  
886-2-8226-1900  
Tel:  
1-3  
 
SC512 Chassis Manual  
1-4 Returning Merchandise for Service  
A receipt or copy of your invoice marked with the date of purchase is required be-  
fore any warranty service will be rendered. You can obtain service by calling your  
vendor for a Returned Merchandise Authorization (RMA) number. When returning  
to the manufacturer, the RMA number should be prominently displayed on the  
outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and  
handling charges will be applied for all orders that must be mailed when service  
is complete.  
supermicro.com/support/rma/).  
Whenever possible, repack the chassis in the original Supermicro carton, using the  
original packaging material. If these are no longer available, be sure to pack the  
chassis securely, using packaging material to surround the chassis so that it does  
not shift within the carton and become damaged during shipping.  
This warranty only covers normal consumer use and does not cover damages in-  
curred in shipping or from failure due to the alteration, misuse, abuse or improper  
maintenance of products.  
During the warranty period, contact your distributor first for any product problems.  
1-4  
 
Chapter 2: System Safety  
Chapter 2  
System Safety  
2-1 Overview  
This chapter provides a quick setup checklist to get your chassis up and running.  
Following the steps in order given should enable you to have your chassis setup and  
operational within a minimal amount of time. This quick setup assumes that you are  
an experienced technician, famailiar with common concepts and terminology.  
2-2 Warnings and Precautions  
You should inspect the box the chassis was shipped in and note if it was damaged  
in any way. If the chassis itself shows damage, file a damage claim with carrier  
who delivered your system.  
Decide on a suitable location for the rack unit that will hold that chassis. It should  
be situated in a clean, dust-free area that is well venilated. Avoid areas where heat,  
electrical noise and eletromagnetic fields are generated.  
You will also need it placed near at least one grounded power outlet. When config-  
ured, the SC512 chassis includes one power supply.  
2-3 Preparing for Setup  
The SC512 chassis includes a set of rail assemblies, including mounting brackets  
and mounting screws you will need to install the systems into the rack. Please read  
this manual in its entirety before you begin the installation procedure.  
2-4 Electrical Safety Precautions  
Basic electrical safety precautions should be followed to protect yourself from harm  
and the SC512 from damage:  
Be aware of the locations of the power on/off switch on the chassis as well  
as the room’s emergency power-off switch, disconnection switch or electrical  
outlet. If an electrical accident occurs, you can then quickly remove power from  
the system.  
Do not work alone when working with high-voltage components.  
2-1  
 
SC512F Chassis Manual  
Power should always be disconnected from the system when removing or in-  
stalling main system components, such as the serverboard, memory modules  
and the DVD-ROM and floppy drives (not necessary for hot-swappable drives).  
When disconnecting power, you should first power down the system with the  
operating system and then unplug the power cords from all the power supply  
modules in the system.  
When working around exposed electrical circuits, another person who is fa-  
miliar with the power-off controls should be nearby to switch off the power, if  
necessary.  
Use only one hand when working with powered-on electrical equipment. This  
is to avoid making a complete circuit, which will cause electrical shock. Use  
extreme caution when using metal tools, which can easily damage any electrical  
components or circuit boards they come into contact with.  
Do not use mats designed to decrease electrostatic discharge as protection from  
electrical shock. Instead, use rubber mats that have been specifically designed  
as electrical insulators.  
The power cord must include a grounding plug and must be plugged into a  
grounded electrical outlet.  
Serverboard battery: CAUTION - There is a danger of explosion if the onboard  
battery is installed upside down, which will reverse its polarities This battery  
must be replaced only with the same or an equivalent type recommended by  
the manufacturer. Dispose of used batteries according to the manufacturer’s  
instructions.  
DVD-ROM laser: CAUTION - This server may have come equipped with a  
DVD-ROM drive. To prevent direct exposure to the laser beam and hazardous  
radiation exposure, do not open the enclosure or use the unit in any uncon-  
ventional way.  
2-2  
 
Chapter 2: System Safety  
2-5 General Safety Precautions  
Keep the area around the chassis clean and free of clutter.  
Place the chassis top cover and any system components that have been re-  
moved away from the system or on a table so that they won’t accidentally be  
stepped on.  
While working on the system, do not wear loose clothing such as neckties and  
unbuttoned shirt sleeves, which can come into contact with electrical circuits or  
be pulled into a cooling fan.  
Remove any jewelry or metal objects from your body, which are excellent metal  
conductors that can create short circuits and harm you if they come into contact  
with printed circuit boards or areas where power is present.  
After accessing the inside of the system, close the system back up and secure  
it to the rack unit with the retention screws after ensuring that all connections  
have been made.  
2-6 System Safety  
Electrostatic discharge (ESD) is generated by two objects with different electrical  
charges coming into contact with each other. An electrical discharge is created to  
neutralize this difference, which can damage electronic components and printed  
circuit boards. The following measures are generally sufficient to neutralize this  
difference before contact is made to protect your equipment from ESD:  
Do not use mats designed to decrease electrostatic discharge as protection from  
electrical shock. Instead, use rubber mats that have been specifically designed  
as electrical insulators.  
Use a grounded wrist strap designed to prevent static discharge.  
Keep all components and printed circuit boards (PCBs) in their antistatic bags  
until ready for use.  
Touch a grounded metal object before removing any board from its antistatic  
bag.  
2-3  
 
SC512F Chassis Manual  
Do not let components or PCBs come into contact with your clothing, which may  
retain a charge even if you are wearing a wrist strap.  
Handle a board by its edges only; do not touch its components, peripheral chips,  
memory modules or contacts.  
When handling chips or modules, avoid touching their pins.  
Put the serverboard and peripherals back into their antistatic bags when not  
in use.  
For grounding purposes, make sure your computer chassis provides excellent  
conductivity between the power supply, the case, the mounting fasteners and  
the serverboard.  
2-4  
 
Chapter 3: Chassis Components  
Chapter 3  
Chassis Components  
3-1 Overview  
This chapter describes the most common components included with your chassis.  
Some components listed may not be included or compatible with your particular  
chassis model. For more information, see the installation instructions detailed later  
in this manual.  
3-2 Components  
Chassis  
Depending on the model, the SC512 chassis may include one slim DVD-ROM/CD-  
ROM bay, at least one fixed hard drive, a floppy drive, and/or two USB ports. For  
Fans  
The SC512 model chassis accepts two or three system fans powered by the moth-  
erboard. These fans are 1U high and are powered by 3-pin connectors.  
Blower  
The SC512, SC512L and SC512C model chassis use a single blower unit for  
system cooling.  
Mounting Rails  
The SC512 can be placed in a rack for secure storage and use. To set up your  
rack, follow the step-by-step instructions included in this manual. SC512 models  
with narrow chassis designs include specialized rails for mounting in a standard  
rack. See the Rack Installation section of this manual for details.  
3-1  
 
SC512 Chassis Manual  
Power Supply  
Each SC512 chassis model includes a high-efficiency power supply rated at 200,  
260, 280, 350, 410 or 580 Watts. In the unlikely event your power supply fails,  
replacement is simple and can be done without tools.  
Air Shroud  
Air shrouds are shields, usually plastic, that funnel air directly to where it is needed.  
Always use the air shroud included with your chassis.  
3-3 Where to get Replacement Components  
Though not frequently, you may need replacement parts for your system. To en-  
sure the highest level of professional service and technical support, we strongly  
recommend purchasing exclusively from our Supermicro Authorized Distributors/  
System Integrators/Resellers. A list of Supermicro Authorized Distributors/System  
to Buy link.  
3-4 Chassis Model Options  
The following section lists the different options which are available for each of the  
different chassis models in the SC512 chassis family of products.  
Identifying Fan and Blower-Cooled Chassis Models  
Your SC512 chassis is equipped with either a blower unit or a set of system fans  
for optimized chassis cooling.  
The SC512, SC512C and most SC512L model chassis use a blower unit for chas-  
sis cooling.  
The SC512F model chassis are cooled with system fans. The number of system  
fans included in your specific system may vary.  
See the following page for illustrations of blower units and system fans. For detailed  
instructions on replacing a blower unit or system fans, see the Chassis Setup and  
Maintenance section of this manual.  
3-2  
 
Chapter 3: Chassis Components  
Air blower unit  
included in chassis  
models SC512,  
SC512C and SC512L  
Figure 3-1: Blower-Cooled Chassis Model  
System fans included  
in chassis model  
SC512F  
Figure 3-2: Fan-Cooled Chassis Model  
3-3  
 
SC512 Chassis Manual  
Model SC512  
Includes a slot with a dummy cover plate where an optional DVD-ROM drive may  
be installed, and a 200 or 260 Watt power supply. The SC512 model chassis is  
cooled with an internal blower unit.  
Dummy Cover  
Plate for Optional  
DVD Drive  
Figure 3-3: Chassis Model SC512-200, SC512-260  
SC512-200  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard Blower Optional  
DVD  
-
2x  
USB  
UP  
FH  
1x  
Fixed  
3.5"  
200 Watt  
High-  
Efficiency  
SC512-260  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard Blower Optional  
DVD  
-
2x  
USB  
UP  
FH  
1x  
Fixed  
3.5"  
260 Watt  
3-4  
 
Chapter 3: Chassis Components  
Model SC512C  
The SC512C includes a CD-ROM drive, floppy drive, USB ports and a 200 or 260  
Watt power supply. The SC512C model chassis is cooled with an internal blower  
unit.  
CD-ROM Drive  
USB Ports  
Floppy Drive  
Figure 3-4: Chassis Model SC512C  
SC512C-200  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard  
Blower  
1x CD  
1x  
2x  
UP  
FH  
1x  
200  
Floppy USB  
Fixed  
3.5"  
Watt  
SC512C-260  
Chassis Blower/  
Fan  
DVD/  
CD  
Floppy USB CPU  
I/O  
Slots  
HDD  
Power  
Supply  
Standard  
Blower  
1x CD  
1x  
2x  
UP  
FH  
1x  
260  
Floppy USB  
Fixed  
3.5"  
Watt  
3-5  
 
SC512 Chassis Manual  
Model SC512F  
The SC512F models may include a DVD-ROM drive, USB ports and a 260, 280,  
350, 410, 520 or 600 Watt power supply. The SC512F-280 and 350 models can sup-  
port a second optional hard disk drive. The SC512F-280/350/410/520/ 600 model  
chassis have a wider chassis design, which mounts in a standard rack utilizing  
special mounting rails. See the Rack Installation section of this manual for details.  
All SC512F model chassis are cooled with system fans.  
DVD-ROM Drive  
Figure 3-5: Chassis Model SC512F-260  
SC512F-260  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Narrow*  
2x Fan  
1x DVD  
-
2x  
UP  
FH  
1x  
260 Watt  
USB  
Fixed  
3.5"  
* Note: Narrow chassis models include specialized mounting rails to fit into a stan-  
dard rack. See the Rack Installation section of this manual for details.  
DVD-ROM Drive  
Figure 3-6: Chassis Model SC512F-280  
SC512F-280  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard 2x Fan  
1x DVD  
-
-
DP/  
UP  
FH  
2x  
Fixed  
3.5"  
280 Watt  
High-  
Efficiency  
Optional DVD-ROM Drive  
Figure 3-7: Chassis Model SC512F-350  
SC512F-350  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard 2x Fan Optional  
DVD  
-
-
DP/  
UP  
FH  
2x  
Fixed  
3.5"  
350 Watt  
Gold-  
Level  
3-6  
 
Chapter 3: Chassis Components  
USB Ports  
DVD-ROM Drive  
Figure 3-8: Chassis Models SC512F-410 and SC512F-520  
SC512F-520  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard 3x Fans 1x DVD  
-
2x  
DP/  
FH  
1x  
Fixed  
3.5"  
520 Watt  
High-  
Efficiency  
USB UP  
SC512F-410  
Chassis Blower/  
Fan  
DVD/  
CD  
Floppy USB CPU  
I/O  
Slots  
HDD  
Power  
Supply  
Standard 3x Fans 1x DVD  
-
2x  
USB  
DP/  
UP  
FH  
1x  
Fixed  
3.5"  
410 DC  
Optional DVD-ROM  
Figure 3-9: Chassis Model SC512F-600  
SC512F-600  
Chassis Blower/  
Fan  
DVD/  
CD  
Floppy USB CPU  
I/O  
Slots  
HDD  
Power  
Supply  
Standard  
3x Fan Optional  
DVD  
-
2x  
USB  
DP/  
UP  
FH  
1x  
Fixed  
3.5"  
600  
Watt  
Gold  
Level  
3-7  
 
SC512 Chassis Manual  
Figure 3-10: Chassis Model SC512F-520L and SC512F-600L  
SC512F-520L  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard 3x Fans  
-
-
-
DP/  
UP  
FH  
1x  
Fixed  
520 Watt  
High  
3.5" Efficiency  
SC512F-600L  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard 3x Fans  
-
-
-
DP/  
UP  
FH  
1x  
Fixed  
3.5"  
600 Watt  
Gold  
Level  
3-8  
 
Chapter 3: Chassis Components  
Model SC512L  
The SC512L models include two 3.5" hard disk drives and a 200 or 260 Watt power  
supply. The SC512L model chassis is cooled with an internal blower unit.  
Figure 3-11: Chassis Models SC512L-200 and SC512L-260  
SC512L-200  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard Blower  
-
-
-
UP  
FH  
2x  
200  
Fixed  
3.5"  
Watt  
SC512L-260  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard Blower  
-
-
-
UP  
FH  
2x  
260  
Fixed  
3.5"  
Watt  
Figure 3-12: Chassis Model SC512L-260-LCD  
SC512L-260(B)-LCD  
Chassis Blower/ DVD/CD Floppy USB CPU  
Fan  
I/O  
Slots  
HDD  
Power  
Supply  
Standard  
Blower  
-
-
-
UP  
FH  
1x  
260  
Fixed  
3.5"  
Watt  
3-9  
 
SC512 Chassis Manual  
Notes  
3-10  
 
Chapter 4: System Interface  
Chapter 4  
System Interface  
4-1 Overview  
There are several LEDs on the control panel and on the drive carriers to keep you  
constantly informed of the overall status of the system, as well as the activity and  
health of specific components. Most SC512 models have two buttons on the chassis  
control panel: a reset button and an on/off switch. This chapter explains the mean-  
ings of all LED indicators and the appropriate response you may need to take.  
Figure 4-1: Chassis LED and Buttons  
4-1  
 
SC512 Chassis Manual  
4-2 Control Panel Buttons  
There are two push-buttons located on the front of the chassis. These are a reset  
button and a power on/off button.  
Reset: The reset button is used to reboot the system.  
Power: The main power switch is used to apply or remove power from the  
power supply to the server system. Turning off system power with this button re-  
moves the main power but keeps standby power supplied to the system. Therefore,  
you must unplug system before servicing.  
4-3 Control Panel LEDs  
The control panel located on the front of the SC512 chassis has five LEDs. These  
LEDs provide you with critical information related to different parts of the system.  
This section explains what each LED indicates when illuminated and any corrective  
action you may need to take.  
Overheat/Fan Fail: When this LED flashes it indicates a fan failure. When  
continuously on (not flashing) it indicates an overheat condition, which may be  
caused by cables obstructing the airflow in the system or the ambient room tem-  
perature being too warm. Check the routing of the cables and make sure all fans  
are present and operating normally. You should also check to make sure that the  
chassis covers are installed. Finally, verify that the heatsinks are installed properly.  
This LED will remain flashing or on as long as the overheat condition exists.  
4-2  
 
Chapter 4: System Interface  
NIC2: Indicates network activity on GLAN2 when flashing.  
NIC1: Indicates network activity on GLAN1 when flashing.  
HDD: Indicates IDE channel activity. SAS/SATA drive, SCSI drive, and/or  
DVD-ROM drive activity when flashing.  
Power: Indicates power is being supplied to the system's power supply units.  
This LED should normally be illuminated when the system is operating.  
4-3  
 
SC512 Chassis Manual  
Notes  
4-4  
 
Chapter 5: Chassis Setup and Maintenance  
Chapter 5  
Chassis Setup and Maintenance  
5-1 Overview  
This chapter covers the steps required to install components and perform mainte-  
nance on the chassis. The only tool you will need to install components and perform  
maintenance is a Phillips head and a flathead screwdriver. Print this page to use  
as a reference while setting up your chassis.  
5-2 Installation Procedures  
Removing the Chassis Cover  
Installing the Hard Drive  
Installing the Motherboard (includes I/O Shield and Expansion Card Slot setup)  
Installing the DVD or CD-ROM Drive  
Installing the Air Shroud  
General Maintenance  
Systems Fans  
Power Supply  
Certain motherboards and heatsinks may not be compatible  
with this chassis. Before installation, review the motherboard  
installation procedures in this chapter.  
!
Review the warnings and precautions listed in the manual be-  
fore setting up or servicing this chassis. These include infor-  
mation in Chapter 2: System Safety and the warning/precau-  
tions listed in the setup instructions.  
!
5-1  
 
SC512 Chassis Manual  
5-3 Removing the Chassis Cover  
Remove these screws  
Remove these screws  
Flat head  
6-32 x 5 mm  
[0.197]  
Remove this screw  
Figure 5-1: Removing the Chassis Cover  
Removing the Chassis Cover  
1. Remove the screws holding the chassis cover in place.  
2. Apply pressure to the middle front of the chassis cover.  
3. Slide the cover toward the rear of the chassis.  
Warning: Except for short periods of time, do NOT operate the  
server without the cover in place. The chassis cover must be in  
place to allow proper airflow and prevent overheating.  
!
5-2  
 
Chapter 5: Chassis Setup and Maintenance  
5-4 Installing Hard Drives  
Remove these screws  
Flat head  
6-32 x 5 mm  
[0.197]  
DVD-ROM/CD-ROM  
Drive  
Figure 5-2: Removing the CD-ROM Drive to Access the Hard Drive  
Installing a Hard Drive  
Before adding a hard drive, you must remove the DVD-ROM/CD-ROM drive.  
1. Open the chassis cover.  
2. If you have not already done so, remove the fan tray. For more information on  
removing the fan tray, see the Maintenance section located at the end of this  
chapter.  
3. Remove the CD-ROM drive. To do this, remove the two screws holding the  
drive in place. One screw is external. The other is internal.  
5-3  
 
SC512 Chassis Manual  
Hard Drive  
Flat head  
6-32 x 5 mm  
[0.197]  
Figure 5-3: Adding the Hard Drive  
4. Place the hard drive in the chassis as illustrated. Make sure the hard drive con-  
nectors face the inside of the chassis.  
5. Secure the hard drive to the chassis using the four screws.  
6. SC512F-280, SC512L and SC512L-260 model users: These chassis can support  
a second hard drive. Insert the second hard drive at this time. If you are are not  
using the models listed above, skip this step.  
Hard Drive  
Second Hard  
Drive  
Flat head  
6-32 x 5 mm  
[0.197]  
Figure 5-4: Adding a Second Hard Drive  
5-4  
 
Chapter 5: Chassis Setup and Maintenance  
5-5 Installing the Motherboard  
Flat head  
6-32 x 5 mm  
[0.197]  
Figure 5-5: The SC512 Backplate (I/O Shield)  
Important Motherboard Installation Information  
Before installing the motherboard, be aware of the following:  
I/O Shield Backplate  
The backplate holds the motherboard ports in place. Your motherboard must match  
SC512 backplate. If your motherboard does not match, you must choose a different  
motherboard.  
Heatsinks  
Some compatible motherboards require heatsinks to lower the temperature of the  
components. Heatsinks for the SC512 chassis must be rated for 1U or less.  
5-5  
 
SC512 Chassis Manual  
Standoffs  
Standoffs prevent short circuits by securing space between the motherboard and  
the chassis surface. The SC512 chassis includes permanent standoffs in locations  
used by most motherboards. These standoffs accept the rounded Phillips head  
screws included in the SC512 accessories packaging.  
Round head  
3 x 5 mm  
[0.197]  
Figure 5-6: Installing the Motherboard  
Installing the Motherboard  
1. Review the documentation that came with your motherboard. Become familiar  
with component placement, requirements, precautions, and cable connec-  
tions.  
2. Open the chassis cover.  
3. Align the motherboard with the chassis standoffs and carefully, place the  
motherboard in the chassis. Make sure rear ports line up with the I/O shield.  
4. Secure the motherboard to the chassis using the ten rounded, Phillips head  
screws supplied with the accessories kit.  
5. Secure the CPU(s), heatsinks, and other components to the motherboard as  
described in the motherboard documentation. Do not exceed eight pounds of  
torque when tightening down the motherboard.  
6. Connect the cables between the motherboard, backplane, chassis, front  
panel, and power supply, as needed.  
5-6  
 
Chapter 5: Chassis Setup and Maintenance  
5-6 Installing the DVD or CD-ROM Drive  
Replace these screws  
Flat head  
6-32 x 5 mm  
[0.197]  
DVD-ROM/CD-ROM  
Drive  
Hard Drive  
Figure 5-7: Replace the DVD-ROM/CD-ROM Drive  
Replacing the DVD or CD-ROM  
1. Place the DVD-ROM or CD-ROM drive in the chassis above the hard drive.  
2. Secure the drive with two screws. One screw is external. The other screw is  
internal.  
5-7  
 
SC512 Chassis Manual  
Expansion Slot Setup  
SC512 chassis includes a slot for one full height/full length add-on card and a riser  
card. The riser card allows the expansion card to fit within the small 1U form.  
The expansion card slot does not require a screw to hold the card in place.  
Add-on Card Slot Latch  
Expansion Card  
Slot Shield  
Figure 5-8: Installing the Expansion Card  
Installing Expansion Cards  
1. Disconnect the power supply, lay the chassis on a flat surface, and open the  
chassis cover.  
2. Slide the add-on card clip upward.  
3. Slide the add-on card slot shield toward the side of the chassis and remove  
the Shield.  
4. Secure the riser card to the motherboard.  
5. Slide the add-on card (with "L" bracket) into the add-on card slot and the riser  
card.  
6. Replace the add-on card slot clip to secure the add-on card.  
5-8  
 
Chapter 5: Chassis Setup and Maintenance  
5-7 Installing the Air Shroud  
The air shroud helps cool the chassis by directing heated air through the rear of  
the chassis. When installing the air fan, be aware of the following:  
The air shroud is designed to fit within the chassis. The sides of the air  
shroud should remain straight in relation to the top. Do not fold or bend the  
air shroud.  
The air shroud has perforated tabs that can be removed if motherboard com-  
ponents prevent proper air shroud installation. Do not remove a tab unless it  
is necessary.  
Incorrect  
Incorrect  
Correct  
Figure 5-9: Air Shroud Placement  
Perforated Tabs  
Figure 5-10: Installing the Air Shroud in the SC512 Chassis  
Installing The Air Shroud  
1. Confirm that the air shroud matches your chassis model.  
2. Place the air shroud in the chassis. The shroud sets directly behind the sys-  
tem fans. If necessary, remove some perforated tabs to ensure a snug fit.  
5-9  
 
SC512 Chassis Manual  
Checking the Airflow in the Chassis  
1. Make sure there are no objects to obstruct airflow in and out of the server.  
2. Do not operate the server without drives or drive trays in the drive bays. Use  
only recommended server parts.  
3. Make sure no wires or foreign objects obstruct air flow through the chassis.  
Pull all excess cabling out of the airflow path or use shorter cables.  
The control panel LEDs inform you of system status. See “Chapter 3: System  
Interface” for details on the LEDs and the control panel buttons.  
Installation Complete  
In most cases, the chassis power supply and fans are pre-installed. If you need to  
install fans continue to the Systems Fan section of this chapter. If the chassis will be  
installed into a rack, continue to the next chapter for rack installation instructions.  
5-10  
 
Chapter 5: Chassis Setup and Maintenance  
5-8 System Fans  
Three heavy duty fans provide cooling for the chassis. These fans circulate air  
through the chassis as a means of lowering the chassis internal temperature.  
The SC512F-280 chassis accepts two fans instead of three.  
System Fan Tray  
Fan Tray Support Pin  
Rubber Grommet  
Figure 5-11: Placing the System Fan  
System Fan Tray  
Systems fan trays are components that house groups of fans. The system fan tray  
is held in place by two rivets permanently attached to the chassis surface. Each  
rivet is encircled by a rubber grommet to reduce vibration.  
5-11  
 
SC512 Chassis Manual  
System Fan Tray Replacement  
Installing the System Fan Tray  
1. Power down the system.  
2. Disconnect each fan from the motherboard.  
3. Lift the system fan tray and fans from the chassis. Retain the rubber mount-  
ings that encircle the tray rivets.  
4. Place the fans into the new system fan tray. Make all the fans face the correct  
direction.  
5. Confirm the the rubber mountings are in place around the chassis rivets.  
6. Align the fan tray with rivets and place the new fan tray (and system fans)  
into the chassis.  
7. Reconnect the system fans to the motherboard  
Replacing Individual System Fans  
Fans can be replaced individually without removing the system fan tray. There is  
no need to power down the system when replacing a system fan.  
Replacing System Fans  
1. If necessary, open the chassis while the power is running to determine which  
fan has failed. (Never run the server for an extended period of time with the  
chassis open.)  
2. Remove the failed fan's power cord from the serverboard.  
3. Lift the failed fan completely from the chassis.  
4. Place the new fan into the vacant space. Make sure the arrows on the top of  
the fan (indicating air direction) point in the same direction as the arrows on  
the other fan(s).  
5. Confirm that the fan is working properly and replace the chassis cover..  
5-12  
 
Chapter 5: Chassis Setup and Maintenance  
5-9 Power Supply  
Depending on your chassis model the SC512 chassis has a 200, 269, 280, 350,  
410 or 520 Watt power supply. This power supply is auto-switching capable. This  
enables it to automatically sense and operate at a 100v to 240v input voltage. An  
amber light will be illuminated on the power supply when the power is off. An il-  
luminated green light indicates that the power supply is operating.  
Power Supply Failure  
The SC512 series chassis has one power supply. In the unlikely event that the power  
supply unit fails, the system will shut down and you will need to replace it.  
Replacement units can be ordered directly from Supermicro (see contact information  
in the preface) or an authorized reseller.  
5-13  
 
SC512 Chassis Manual  
Remove these screws  
Power Supply  
Pan Head  
6-32 x 5mm  
[0.197]  
Remove this screw  
Figure 5-12: Removing the Power Supply  
Replacing the Power Supply  
1. Disconnect the power cord from the from the chassis to ensure that the unit is  
not accidentally plugged in.  
2. Place the chassis on a stable hard surface and remove the chassis cover.  
3. Disconnect the power supply from the motherboard and other chassis compo-  
nents.  
4. Remove the screws securing the power supply. Two screws are in the back  
of the chassis and one underneath. Retain the screws and the internal brace  
that connects the power supply to the chassis from underneath.  
5. Pull the power supply out of the chassis.  
6. Place the new power supply into the chassis and secure the power supply  
using the three screws and internal brace.  
7. Connect the power supply to the motherboard and other chassis components.  
8. Connect the power cord to the power supply and power up the chassis/server.  
9. Once you confirm that the power supply has been installed correctly, replace  
the chassis cover.  
5-14  
 
Chapter 5: Chassis Setup and Maintenance  
Figure 5-13: Replacing the LED Panel  
Replacing the Chassis LED Panel  
In the unlikely event that the chassis LED and buttons fail, you can replace the panel.  
Replacement parts can be ordered from Supermicro or an authorized reseller.  
Replacing the Chassis LED Panel  
1. Power down and unplug the system.  
2. Remove the chassis cover.  
3. Disconnect the cord to the front panel.  
4. Locate and remove three screws holding the panel in place. (If your chassis  
supports dual hard drives, you may have to remove the second hard drive  
from the chassis).  
5. Install the new LED panel and secure the unit with three screws.  
6. Reconnect the cables to the LED panel and if necessary, replace the hard  
drive.  
5-15  
 
SC512 Chassis Manual  
Notes  
5-16  
 
Chapter 6: Rack Installation  
Chapter 6  
Rack Installation  
6-1 Overview  
This chapter provides a quick setup checklist to install the chassis into a rack.  
6-2 Unpacking the System  
You should inspect the box the chassis was shipped in and note if it was damaged  
in any way. If the chassis itself shows damage you should file a damage claim with  
the carrier who delivered it.  
Decide on a suitable location for the rack unit that will hold your chassis. It should  
be situated in a clean, dust-free area that is well ventilated. Avoid areas where  
heat, electrical noise and electromagnetic fields are generated. You will also need  
it placed near a grounded power outlet. Be sure to read the Rack and Server Pre-  
cautions in the next section.  
6-3 Preparing for Setup  
The box your chassis was shipped in should include two sets of rail assemblies,  
two rail mounting brackets and the mounting screws you will need to install the  
system into the rack. Please read this section in its entirety before you begin the  
installation procedure outlined in the sections that follow.  
Choosing a Setup Location  
Leave enough clearance in front of the rack to enable you to open the front  
door completely (~25 inches).  
Leave approximately 30 inches of clearance in the back of the rack to allow for  
sufficient airflow and ease in servicing.  
This product is for installation only in a Restricted Access Location (dedicated  
equipment rooms, service closets and the like).  
6-1  
 
SC512 Chassis Manual  
Warnings and Precautions!  
!
!
Rack Precautions  
Ensure that the leveling jacks on the bottom of the rack are fully extended to  
the floor with the full weight of the rack resting on them.  
In single rack installation, stabilizers should be attached to the rack.  
In multiple rack installations, the racks should be coupled together.  
Always make sure the rack is stable before extending a component from the  
rack.  
You should extend only one component at a time - extending two or more si-  
multaneously may cause the rack to become unstable.  
General Server Precautions  
Review the electrical and general safety precautions that came with the com-  
ponents you are adding to your chassis.  
Determine the placement of each component in the rack before you install the  
rails.  
Install the heaviest server components on the bottom of the rack first, and then  
work up.  
Use a regulating uninterruptible power supply (UPS) to protect the server from  
power surges, voltage spikes and to keep your system operating in case of a  
power failure.  
Allow the hot plug hard drives and power supply modules to cool before touch-  
ing them.  
Always keep the rack's front door and all panels and components on the servers  
closed when not servicing to maintain proper cooling.  
6-2  
 
Chapter 6: Rack Installation  
Rack Mounting Considerations  
Ambient Operating Temperature  
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-  
ture of the rack environment may be greater than the ambient temperature of the  
room. Therefore, consideration should be given to installing the equipment in an  
environment compatible with the manufacturer’s maximum rated ambient tempera-  
ture (Tmra).  
Reduced Airflow  
Equipment should be mounted into a rack so that the amount of airflow required  
for safe operation is not compromised.  
Mechanical Loading  
Equipment should be mounted into a rack so that a hazardous condition does not  
arise due to uneven mechanical loading.  
Circuit Overloading  
Consideration should be given to the connection of the equipment to the power  
supply circuitry and the effect that any possible overloading of circuits might have  
on overcurrent protection and power supply wiring. Appropriate consideration of  
equipment nameplate ratings should be used when addressing this concern.  
Reliable Ground  
A reliable ground must be maintained at all times. To ensure this, the rack itself  
should be grounded. Particular attention should be given to power supply connec-  
tions other than the direct connections to the branch circuit (i.e. the use of power  
strips, etc.).  
6-3  
 
SC512 Chassis Manual  
6-4 Rack Mounting Instructions  
This section provides information on installing the SC512 chassis into a rack unit  
with the rails provided. There are a variety of rack units on the market, which  
may mean the assembly procedure will differ slightly. You should also refer to the  
installation instructions that came with the rack unit you are using.  
NOTE: The SC512F-280/350/410/520/600 chassis models are designed with a  
wider chassis. The rails for these chassis will fit a rack between 25.6" and 33.05"  
deep. The following shows how to mount these chassis to a standard rack.  
Identifying the Sections of the Rack Rails (Optional Item)  
The chassis package includes two rack rail assemblies in the rack mounting kit.  
Each assembly consists of two sections: an inner fixed chassis rail that secures  
directly to the server chassis, and an outer fixed rack rail that secures directly to  
the rack itself.  
The SC512F comes with "chassis ears" that allow the chassis to use generic  
rails.  
Inner Rails  
Chassis Ears  
Outer Rails  
Figure 6-1: Identifying the Sections of the Rack Rails  
(Right side rail shown)  
6-4  
 
Chapter 6: Rack Installation  
Installing the Inner Rail Extension  
The SC512F includes chassis ears that you must remove before installing the  
rails.  
Removing the Chassis Ears  
1. Locate and remove the three screws holding the chassis ear in place.  
2. Repeat step on with the other chassis ear.  
Flat head  
M4 x 4 mm  
[0.157]  
Figure 6-2: Installing Inner Rails to the Chassis  
Installing the Inner Rails  
1. Place the inner rail on the side of the chassis aligning the hooks of the chas-  
sis with the rail holes.  
2. Slide the rail toward the front of the chassis to secure the rail in place.  
3. Secure the chassis with four screws.  
4. Repeat steps 1-3 for the other inner rail extension.  
6-5  
 
SC512 Chassis Manual  
Flat head  
M5 x 12 mm [0.472]  
Washer for M5  
Secure to the  
Rear of the Rack  
Attach Outer Racks  
together  
Secure to the  
Front of the Rack  
Figure 6-3: Assembling the Outer Rails  
Installing the Outer Rails to the Rack  
Installing the Outer Rails  
1. Attach the short bracket to the outside of the long bracket. You must align the  
pins with the slides. Also, both bracket ends must face the same direction.  
2. Adjust both the short and long brackets to the proper distance so that the rail  
fits snugly into the rack.  
3. Secure the long bracket to the front side of the outer rail with two M5 screws  
and the short bracket to the rear side of the outer rail with three M5 screws.  
Use a washer with each screw.  
4. Repeat steps 1-4 for the left outer rail.  
6-6  
 
Chapter 6: Rack Installation  
3
1
3
1
2
1
Figure 6-4: Installing the Outer Rails to the Server Rack  
6-7  
 
SC512 Chassis Manual  
Figure 6-5: Installing the Chassis into a Rack  
Installing the Chassis into a Rack  
Installing the Chassis  
1. Confirm that the inner rails are attached to the chassis. Also, confirm that the  
outer rails are installed on the rack.  
2. Align chassis rails with the front of the rack rails.  
3. Slide the chassis rails into the rack rails, keeping the pressure even on both  
sides (you may have to depress the locking tabs when inserting). When the  
server has been pushed completely into the rack, you should hear the locking  
tabs "click" into the locked position.  
4. (Optional) Insert and tightening the thumbscrews that hold the front of the  
server to the rack.  
6-8  
 
Chapter 6: Rack Installation  
Mid-Mount Telco Rack  
The SC512.supports Telco rack installation. The SC512 chassis compact design  
allows the chassis to be installed into a Telco rack without the use of rails.  
Place chassis  
ears here  
Flat head  
M4 x 4 mm  
[0.157]  
Figure 6-6: Moving the Chassis Ears for Telco Rack Installation  
Installing the Chassis into a Rack in Mid-Mount Position  
Instaling into a Mid-Mount Position Rack  
1. If it is necessary to install the chassis in a mid-mount Telco rack, remove the  
chassis rails and the chassis ears (if the ears are installed at the front of the  
chassis).  
2. Locate the three screw holes in the middle of the chassis and secure the ears  
to the chassis with three flat head screws. Make sure the screws are secure,  
but do not over tighten the screws.  
6-9  
 
SC512 Chassis Manual  
Flat head  
M5 x 12 mm [0.472]  
Washer for M5  
Figure 6-7: Installing the Server into a Telco Rack  
3. Hold the chassis in the telco rack and screw the chassis to the rack using the  
three screw holes located in the chassis ears.  
4. The chassis is held in place by the chassis ears and does not slide in and out  
of place.  
6-10  
 
Appendix A: SC512 Chassis Cables  
Appendix A  
Cables, Screws,  
and Other Accessories  
A-1 Overview  
This appendix lists supported cables for your chassis system. It only includes the  
most commonly used components and configurations. For more compatible cables,  
refer to the manufacturer of the motherboard you are using and our Web site at:  
A-2 Cables Included with SC512 Chassis  
SC512-200 and SC512-260  
Part #  
Type  
Cable  
Wire  
Length  
Description  
CBL-0049L  
Front cable 16-pin to 16-pin  
CBL-0084L  
CBL-0260L  
CBL-0261L  
9 cm  
DVD cable (lead free).  
US power cord 18 AWG  
40cm 7-pin SATA cable S-RA  
Cable  
Cable  
Cable  
40cm  
4-pin to 1x SATA (RA) + 1x 4-pin  
(RA) + 1x FPD PWS  
CBL-0262L  
CBL-0263L  
77cm  
9-pin to 9-pin internal USB cable  
SC512F-260  
Length  
Part #  
Type  
Cable  
Wire  
Description  
CBL-0049L  
Front cable 16-pin to 16-pin  
CBL-0084L  
CBL-0260L  
9 cm  
DVD cable (lead free).  
US power cord 18 AWG  
4-pin to 1x SATA (RA) + 1x 4-pin  
(RA) + 1x FPD PWS  
CBL-0262L  
CBL-0263L  
Cable  
Cable  
77cm  
9-pin to 9-pin internal USB cable  
A-1  
 
SC512 Chassis Manual  
SC512F-280  
Length  
Part #  
Type  
Description  
7-pin SATA with two 90 degree side  
connectors (lead free).  
CBL-0142L  
Cable  
30 cm (~12")  
CBL-0156L  
CBL-0084L  
-
Cable  
Wire  
40 cm  
9 cm  
6'  
16-pin to 16-pin FP cable. Lead free.  
DVD cable. Lead free.  
Cable  
Regional power cord  
SC512F-350  
Part #  
Type  
Cable  
Cable  
Cord  
Length  
30cm  
40cm  
6 feet  
40cm  
Description  
CBL-0142L  
CBL-0156L  
CBL-0260L  
CBL-0261L  
7-pin 2-side SATA RA-RA cable  
Front ctrl cable round 16 to 16-pin  
US power cord 18AWG  
Cable  
7pin SATA cable S-RA  
4-pin to 1x SATA (RA) + 1x4-pin  
(RA) + 1x FPD PWS EXT. cable  
CBL-0262L  
Cable  
-
SC512F-410  
Part #  
Type  
Length  
Description  
7-pin SATA with two 90 degree side  
connectors (lead free).  
CBL-0142L  
Cable  
30 cm (~12")  
CBL-0156L  
CBL-0084L  
Cable  
Wire  
40 cm  
9 cm  
16-pin to 16-pin FP cable. Lead free.  
DVD cable. Lead free.  
SC512F-520  
Part #  
Type  
Length  
Description  
7-pin SATA with two 90 degree side  
connectors (lead free).  
CBL-0142L  
Cable  
30 cm (~12")  
CBL-0156L  
CBL-0084L  
-
Cable  
Wire  
40 cm  
9 cm  
6'  
16 pin to 16 pin FP cable. Lead free.  
DVD Cable. Lead free.  
Cable  
Regional power cord  
SC512F-600  
Part #  
Type  
Length  
Description  
7-pin SATA with two 90 degree side  
connectors (lead free).  
CBL-0142L  
Cable  
30 cm (~12")  
16-pin to 16-pin FP Cable. Lead  
Free.  
CBL-0156L  
-
Cable  
Cable  
40 cm  
6'  
Regional power cord  
A-2  
 
Appendix A: SC512 Chassis Cables  
SC512F-520L and SC512F-600L  
Part #  
Type  
Length  
Description  
7-pin SATA with two 90 degree side  
connectors (lead free).  
CBL-0142L  
Cable  
30 cm (~12")  
16-pin to 16-pin FP Cable. Lead  
Free.  
CBL-0156L  
-
Cable  
Cable  
40 cm  
6'  
Regional power cord  
SC512L-200 and SC512L-260  
Part #  
Type  
Length  
Description  
CBL-0049L  
Cable  
Wire  
Front cable 16-pin to 16-pin  
CBL-0084L  
CBL-0260L  
CBL-0261L  
9 cm  
DVD cable (lead free).  
US power cord 18 AWG  
40cm 7-pin SATA cable S-RA  
Cable  
Cable  
Cable  
40cm  
4-pin to 1x SATA (RA) + 1x 4-pin  
(RA) + 1x FPD PWS  
CBL-0262L  
CBL-0263L  
77cm  
9-pin to 9-pin internal USB cable  
SC512L-260-LCD  
Length  
Part #  
CBL-0049  
CBL-0121  
Type  
Cable  
Description  
9 cm  
16-pin to 16-pin ribbon cable  
10-pin to 4-pin cable for LCD  
USB 2.0  
A-3  
 
SC512 Chassis Manual  
Extending Power Cables  
Although Supermicro chassis are designed with to be efficient and cost-effective,  
some compatible motherboards have power connectors located in different areas.  
To use these motherboards you may have to extend the power cables to the mother  
boards. To do this, use the following chart as a guide.  
Power Cable Extenders  
Number of Pins  
24-pin  
Cable Part #  
CBL-0042  
CBL-0059  
CBL-0062  
CBL-0060  
Length  
7.9”(20 CM)  
7.9”(20 CM)  
7.9”(20 CM)  
7.9”(20 CM)  
20-pin  
8-pin  
4-pin  
Front Panel to the Motherboard  
The SC512 chassis includes a cable to connect the chassis front panel to the  
motherboard. If your motherboard uses a different connector, use the following list  
to find a compatible cable.  
Front Panel to Motherboard Cable (Ribbon Cable)  
Number of Pins  
(Front Panel)  
Number of Pins  
(Motherboard)  
Cable Part #  
16-pin  
16-pin  
20-pin  
16-pin  
20-pin  
16-pin  
20-pin  
20-pin  
varies*  
varies*  
CBL-0049  
CBL-0048  
CBL-0047  
CBL-0068  
CBL-0067  
* Split cables: Use these cable if your motherboard requires several different con-  
nections from the front panel.  
A-4  
 
Appendix A: SC512 Chassis Cables  
A-3 Routing the Chassis Cables  
In order for the SC512 chassis to perform safely and efficiently, it is important that the  
cables are routed correctly. Follow the instructions below and review both the cabling  
diagram and photograph to ensure that the cabling has been properly routed.  
Preparing the Chassis for Cable Routing  
1. Unplug the chassis from any power source.  
2. Review the diagram on the following page, taking note of the naming of each  
cable.  
3. Remove the screws securing the fan platform to the bottom of the chassis.  
PWR  
3C  
1
MOTHERBOARD  
AREA  
1C  
1
MB SATA  
PORTS  
5A  
1
2C  
1
4A  
SATA PWR  
1
(RIGHT ANGLE)  
LEFTMIDDLE BRACKET  
RIGHT MIDDLE BRACKET  
3B  
1
HDD  
HDD  
1B  
FAN  
2B  
1
1
SATA  
(RIGHT ANGLE)  
SATA  
(STRAIGHT)  
SATA PWR  
(RIGHT ANGLE)  
2A  
1
1A  
1
3A  
1
Figure A-1: Chassis Cable Routing Diagram (SC512L-200/260)  
A-5  
 
SC512 Chassis Manual  
Routing Cable (1A) from Hard Drive (1B)  
1. Plug cable (1A) into the SATA port of hard drive (1B).  
2. Lift up the fan and run cable (1A) straight out from the port and under the fan.  
3. Route cable (1A) over the hard drive and through the left middle bracket.  
4. Plug cable (1A) into upper SATA port (1C) on the motherboard.  
Routing Cable (2A) from Hard Drive (2B)  
1. Plug cable (2A) into the SATA port of hard drive (2B).  
2. Run cable (2A) upwards at a right angle, up and over the top of hard drive  
(2B).  
3. Route cable (2A) through the left middle bracket.  
4. Plug cable (2A) into lower SATA port (2C) on the motherboard.  
Routing Split Cable (3A)(4A) from Hard Drives (1B)(2B) to the Power Supply  
1. Plug the end of the split cable (3A) into hard drive (2B).  
2. Route the end of the split cable (3A) straight up at a right angle, beside the  
fan, and over the top of cable (1A).  
3. Plug the end of the split cable (3A) into connector (3B).  
4. Plug the other end of the split cable (4A) into hard drive (1B).  
5. Route the end of the split cable (4A) straight up at a right angle, along the top  
of the fan.  
6. Route cable (5A) through the right middle bracket and plug it into connector  
(3B).  
A-6  
 
Appendix A: SC512 Chassis Cables  
Checking the Cable Routing  
1. Check the cable routing by following out each cable in the previous steps and  
comparing them to the diagram in Figure A-1, and the photograph in Figure  
A-2.  
Figure A-2: Chassis Cable Routing  
A-7  
 
SC512 Chassis Manual  
A-4 Chassis Screws  
The Chassis and accessory box include all the screws needed to setup your  
chassis. This section include descriptions of the most common screws used. Your  
chassis may not require all the parts listed.  
M/B  
HARD DRIVE  
Flat head  
6-32 x 5 mm  
[0.197]  
Pan head  
6-32 x 5 mm  
[0.197]  
DVD-ROM CD-ROM FLOPPY DRIVE  
Flat head  
6-32 x 5 mm  
[0.197]  
Round head  
2.6 x 5 mm  
[0.197]  
Round head  
3 x 5 mm  
[0.197]  
Pan head  
6-32 x 5 mm  
[0.197]  
RAIL  
Flat head  
M4 x 4 mm  
[0.157]  
Round head  
M4 x 4 mm  
[0.157]  
Flat head  
M5 x 12 mm [0.472]  
Washer for M5  
M/B STANDOFF  
M/B standoff  
6-32 to 6-32  
Thumb screw  
6-32 x 5 mm [0.197]  
M/B (CPU) standoff  
M5 to 6-32  
Figure A-3: Chassis Screws  
A-8  
 
Appendix B: SC512F Power Supply Specifications  
Appendix B  
Power Supply Specifications  
This appendix lists power supply specifications for your chassis system.  
SC512 Chassis Model  
200  
PWS-201-1H  
260  
MFR Part #  
PWS-0055  
100 - 240V  
50 - 60Hz  
4 - 2A Max  
100 - 240V  
60 - 50Hz  
4A Max  
Rated AC Voltage  
+5V standby 2.0A  
2.0A  
+12V 16.0A  
+5V 8.0A  
18.0A  
25.0A  
15.0A  
1.0A  
+3.3V 8.0A  
-12V 0.5A  
SC512C Chassis Models  
200  
260  
MFR Part #  
PWS-0043  
PWS-0055  
100 - 240V  
60 - 50Hz  
5 - 3A  
100 - 240V  
60 - 50Hz  
4A Max  
Rated AC Voltage  
+5V standby 2.0A  
2.0A  
+12V 12.0A  
+5V 20A  
18.0A  
25.0A  
15.0A  
1.0A  
+3.3V 17.0 A  
-12V 0.8A  
B-1  
 
SC512 Chassis Manual  
SC512F Chassis Models (See below for 410 model)  
260 280 350 520/520L  
PWS-0055 PWS-281-1H PWS-351-1H PWS-521-1H PWS-601-1H  
600/600L  
MFR  
Part #  
Rated  
AC  
Voltage 4A Max  
100 - 240V 100 - 240V  
100-240 V,  
50-60 Hz,  
4.2 - 1.8A  
100 - 240V  
50 - 60Hz  
7 - 3A  
100 - 240V  
50 - 60Hz  
7.5 - 3.1A  
60 - 50Hz  
50 - 60Hz  
5A Max  
+5V  
2.0A  
2A  
3A  
3A  
3A  
standby  
+12V 18.0A  
+5V 25.0A  
+3.3V 15.0A  
-12V 1.0A  
23A  
18A  
15A  
1A  
29A  
18A  
15A  
-
39A  
20A  
16A  
0.5A  
49A  
20A  
16A  
0.5A  
SC512F-410 Chassis Model  
410  
MFR Part #  
DC Voltage  
PWS-0061  
Voltage Range = -36V to -72V  
Nominal Voltage = -48V  
Max Input Current = 18A @ -48V  
DC Output 5V + 3.3V ≤ 180W  
+5V 35.0A  
+5V standby 3.0A  
+12V 32.0A  
-12V 0.5A  
+3.3V 20.0A  
SC512L Chassis Models  
200  
260/260-LCD  
PWS-0055  
MFR Part #  
PWS-0043  
100 - 240V  
60 - 50Hz  
5-3A  
100 - 240V  
60 - 50Hz  
4A Max  
Rated AC Voltage  
+5V standby 2.0A  
2.0A  
+12V 12.0A  
+5V 20A  
18.0A  
25.0A  
15.0A  
1.0A  
+3.3V 17.0A  
-12V 0.8A  
B-2  
 
Appendix B: SC512F Power Supply Specifications  
Notes  
B-3  
 
SC512 Chassis Manual  
Disclaimer (cont.)  
The products sold by Supermicro are not intended for and will not be used in life sup-  
port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,  
aircraft/emergency communication devices or other critical systems whose failure to per-  
form be reasonably expected to result in significant injury or loss of life or catastrophic  
property damage. Accordingly, Supermicro disclaims any and all liability, and should  
buyer use or sell such products for use in such ultra-hazardous applications, it does so  
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold  
Supermicro harmless for and against any and all claims, demands, actions, litigation,  
and proceedings of any kind arising out of or related to such ultra-hazardous use or  
sale.  
B-4  
 

SMSC Switch SCH5617C User Manual
Snapper Air Cleaner 126T00 User Manual
Soleus Air Air Conditioner 3119233 User Manual
Sony Camcorder ILCE 3000 User Manual
Sony Ericsson Lawn Mower W205a User Manual
Sony Laptop 104 User Manual
Stovax Stove STO0708 User Manual
Sunbeam Food Saver VAC780 User Manual
Sunbeam Vacuum Cleaner SBH 200 User Manual
Tanaka Cultivator TMC 200 User Manual