En g lish
3-866-122-14(1)
Thank you for purchasing the Sony DC adaptor/ charger.
Wh e n t h e CHARGE la m p fla sh e s
A
Fu se Re p la ce m e n t
Sp e cifica t io n s
If a problem occurs during charging, the CHARGE lamp flashes and
WARNING appears on the display.
Check through the following chart.
Before operating the unit, please read this manual thoroughly and retain it
for future reference.
If this unit is not working properly, check to see if the fuse has blown out.
If the fuse has blown out, replace it in the following way.
Power requirements
12/ 24 V DC
(12/ 24 V, only for negative groundedcars)
DC OUT:
The DC-VQ800 car battery charger (only for negative (–) grounded cars) can
be used by connecting to the cigarette lighter socket of a car as follows:
• to charge a lithium ion type battery pack.
The following functions are available with the “InfoLITHIUM” battery
pack:
– Quickly charging
– Remaining charge time display
• to supply power to the Sony video equipment.
Output voltage
1
2
4
5
Remove the battery pack from this unit, then install the same battery
pack again.
8.4 V, 2.0 A in operating mode
Battery charge terminal:
1
2
3
Tw ist the end of the plug and remove it.
8.4 V, 1.4 A in charge mode
Sony battery pack NP-FM50/ FM70/ FM90/
F530/ F550/ F730/ F750/ F930/ F950
0°C to 40°C (32°F to 104°F)
–20°C to 60°C (–4°F to 140°F)
Approx. 136 x 48 x 90 mm (w/ h/ d)
(51/ 3 x 110/ 16 x 3 1/ 2 inches)
Approx. 320 g (11.3 oz)
DC Ad a p t o r/Ch a rg e r
Application
If the CHARGE lamp flashes
again:
If the CHARGE lamp lights and
does not flash again:
Operating temperature
Storage temperature
Dimensions
6
7
Install another battery pack.
If the CHARGE lamp goes out
because the charging time has
passed, there is no problem.
Remove the blow n out fuse.
3
Operating Instructions
Mode d’emploi
Wh a t is t h e “ In fo LITHIUM”
The “InfoLITHIUM” is a lithium ion battery pack which can exchange data
with compatible electronic equipment about its battery consumption. Sony
recommends that you use the “InfoLITHIUM” battery pack with electronic
Mass
Supplied accessories
Connecting cord DK-415 (1), DK-215 (1)
Manual de instrucciones
If the CHARGE lamp flashes
again:
If the CHARGE lamp lights and
does not flash again:
equipment having the
mark.
Design and specifications are subject to change without notice.
Insert the new fuse and tw ist the end of the plug and tighten.
8
qs
qd
The problem is with this unit.
If the CHARGE lamp goes out
because the charging time has
passed, the problem is with the
battery pack first installed.
“InfoLITHIUM” is a trademark of Sony Corporation.
This mark indicates that this product is a genuine
accessory for Sony video products. When purchasing
Sony video products, Sony recommends that you
purchase accessories with this “GENUINE VIDEO
ACCESSORIES” mark.
No t e s
• Replace the fuse with a fuse of the same voltage (4 A, 125 V).
• If the car's cigarette lighter socket is dirty with ash, etc., the plug part will
become hot due to a poor connection. Be sure to clean it before using.
• When replacing the fuse, do not substitute anything for the specified fuse.
• If the fuse blows again soon after replacement, consult your nearest Sony
dealer.
VCR/CAMERA
BATTERY LIFE
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
WARNING
TIME TO CHG
NORMAL FULL
9
0
qf
qg
Please contact your nearest Sony dealer in connection with the product
with the problem.
h
m
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
qa
TM
Id e n t ifyin g t h e p a rt s
Please contact your car dealer about the polarity that your car is grounded
or the voltage of your car battery, etc.
To re m o ve t h e b a t t e ry p a ck
SERIES
See illustration A.
No t e s o n Use
Ab o u t t h e re m a in in g b a t t e ry t im e
While charging the battery pack, this unit will show the remaining battery
time with your video equipment, etc. on the following conditions.
• Using the “InfoLITHIUM” battery pack
• Using the electronic equipment having the
Make sure that you use the battery pack having the
Consult the operating instructions supplied with your video equipment if it
is applied to “InfoLITHIUM”.
NP-F550, e t c. (ill. B-1)
Slide the battery pack in the direction of the arrow,then lift it straight out.
1 Terminal shutter (“InfoLITHIUM” (L series))
2 Terminal shutter (“InfoLITHIUM” (M series))
3 DC OUT connector
4 CHARGE lamp
5 Mode change sw itch
TM
SERIES
B
NP-FM50, e t c. (ill. B-2)
Slide the battery pack in the direction of the arrow,then lift it straight out.
DC-VQ800
Sony Corporation © 1999 Printed in Japan
3
1
6 DISPLAY CHANGE button
7 Display w indow
mark
To Ch e ck Ch a rg in g
While charging, you can check the charging time on the display. After
starting charging in a minute, BATTERY LIFE lights up on the display.
mark.
Disp la y w in d o w
8 “InfoLITHIUM” indicator
9 WARNING indicator
0 TIME TO CHG (charge) indicator
qa Time indicator
qs BATTERY LIFE (battery remaining time) indicator
qd VCR/CAMERA indicator
2
Though the follow ing models are applied to “InfoLITHIUM”, the
remaining battery time is not displayed on this unit.
Press DISPLAY CHANGE w hile charging.
Each time you press DISPLAY CHANGE, the display changes as follows.
Ow n e r’s Re co rd
DCR- SC100/ SC100E/ TRV7/ TRV7E
The model and serial numbers are located on the bottom of the unit.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding
this product.
The remaining battery time
CCD-TR555/ TR555E/ TR610E/ TR710/ TR710E/ TR760E/ TR790E/ TR810E/
TR820E/ TR825E/ TR910/ TR910E/ TR920E/ TR930/ TR1100E/
TR2200E/ TR2300/ TR2300E/ TR3100E/ TR3300/ TR3300E/ TR3400/
TRV31/ TRV31E/ TRV41/ TRV41E/ TRV51/ TRV51E/ TRV54E/
TRV56E/ TRV61E/ TRV62/ TRV64E/ TRV72/ TRV81/ TRV81E/
TRV82/ TRV91E/ TRV94/ TRV94E/ TRV101/ TRV101E/
SC55/ SC55E/ SC65/ SC65E
w hen the battery pack being
charged is attached to your
“InfoLITHIUM” electronic
BATTERY LIFE
m
qf Full charge indicator
qg Remaining battery indicator
equipment
DISPLAY
CHANGE
Model No. DC-VQ800 Serial No.
The time is not displayed when the
remaining battery time is less than 5
minutes.
To remove
1
GV-A500/ A500E
To Ch a rg e t h e Ba t t e ry Pa ck
The remaining time until normal
charge is completed
WARNING
If you use this battery pack with electronic equipment not having the
mark, the remaining battery capacity will not be indicated in minutes.*
See illustration B.
TIME TO CHG
NORMAL
m
To p re ve n t fire o r sh o ck h a za rd , d o n o t
e xp o se t h e u n it t o ra in o r m o ist u re .
1
2
3
Set the mode change sw itch to CHARGE.
Connect the pow er cord to this unit.
DISPLAY
CHANGE
*The indication may not be accurate depending on the condition and environment
which the equipment is used under
Connect the pow er cord to the cigarette lighter socket.
The remaining time until full
charge is completed
Ch a rg in g
The beep sounds and the display window lights up.
TIME TO CHG
FULL
Use only a lithium ion type battery pack. This unit cannot be used to
charge a Ni-Cd/ Nickel hydrogen type battery pack.
• Attach the battery pack firmly.
4
Install the battery pack.
h
m
Charging begins. When the remaining battery indicator becomes
and the CHARGE lamp lights up, normal charge is completed. For full
charge, which allows you to use the battery slightly longer than “normal
charge”, leave the battery pack attached until the CHARGE lamp goes
out.
To remove
DISPLAY
CHANGE
2
• Charge the battery pack on a flat surface without vibration.
Ch a rg in g t e m p e ra t u re
No t e s
The temperature range for charging is 0°C to 40°C (32°F to 104°F).
However, to provide maximum battery efficiency, the recommended
temperature range when charging is 10°C to 30°C (50°F to 86°F).
Remove the battery pack when required. It can be used even if the
charging is not completed.
• The time display shows the approximate time when charging at 10°C -
30°C. The time display may differ from the actual charging time
depending on using conditions and circumstances.
• The time display may show “– – – –” in the following cases. However, the
unit is not malfunctioning.
– The remaining battery time is less than 5 minutes.
– There is a difference between the displayed time and actual charging
time. Even if this happens, continue charging.
• Full charge requires about 1 hour after normal charge is completed. If you
remove the battery pack between normal charge and full charge, the
charging time may not be displayed properly in the next charging.
• If the charging time is not displayed properly, fully charge the battery
pack. The charging time will be displayed properly.
• When you attach a fully charged battery pack to this unit, “TIME TO CHG
FULL 1h” may appear on the display. However, the unit is not
malfunctioning.
• The remaining battery time may not be displayed depending on using
conditions and circumstances of your video camera recorder and of the
battery. See “About the remaining time” for more details.
• You may wait for a while after pressing DISPLAY CHANGE until the
display shows the time indication.
• To display the remaining battery time of a new battery, attach it to your
video camera recorder and use it for about 20 seconds. Then, charge the
battery with this unit.
Re m a in in g b a t t e ry in d ica t o r
Ot h e rs
Normal charge
Full charge
• Use this car battery charger only for cars which use a 12 or 24 volt battery.
• There are cars which are negatively grounded and there are others which
are positively grounded.
This symbol is intended to alert the user to the presence
of uninsulated “Dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
This car battery charger is for negatively grounded cars only.
• Use the unit with leaving the car engine going. If you use the unit with the
car engine stopped, the car battery may become unusable.
• This unit is not disconnected form the power source as long as it is
connected to the cigarette lighter socket of a car.
• Unplug the car battery cord from the cigarette lighter socket when not in
use. To disconnect the cord, pull it out by the plug. Never pull the cord
itself.
• Do not operate the unit with a damaged cord or if it has been dropped or
damaged.
• Be sure that nothing metallic comes into contact with the metal parts of
the unit or connecting plate. If it does, a short may occur and the unit
may be damaged.
To In st a ll t h e b a t t e ry p a ck
C
This symbol is intended to alert the user to the presence
of important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
“ In fo LITHIUM” (L se rie s) (NP-F550, e t c.) (ill. B-1)
1 Place the battery pack on this unit w ith the b mark facing the
terminal shutter (L series).
2 Slide the battery pack in the direction of the arrow .
Press the battery pack until the terminal shutter enters completely
into this unit.
1
CAUTION
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
2
• Always keep the metal contacts clean.
• Do not disassemble or convert the unit.
“ In fo LITHIUM” (M se rie s) (NP-FM50, e t c.) (ill. B-2)
1 Place the battery pack on this unit w ith the B mark facing the
terminal shutter (M series).
2 Slide the battery pack in the direction of the arrow .
Press the battery pack until the terminal shutter lifts completely.
3
The Graphical Symbols with Supplemental Marking is located on the
bottom of the unit.
A
• Do not apply mechanical shock or drop the unit.
• While the unit is in use, it gets warm. But this is normal.
• Keep the unit away from AM receivers, because it will disturb AM
reception.
• Do not place the unit in a location where it will be in direct sunlight such
as on the dashboard.
No t e :
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
To Op e ra t e Vid e o Eq u ip m e n t
No t e
See illustration C.
When you install the battery pack, be sure not to strike it to the terminal of
the DC adaptor/ charger.
If any difficulty should arise, unplug the unit and contact your nearest Sony
dealer.
Use the supplied DK-415 or DK-215 connecting cord.
For details of the connection, refer to the instruction manual of your video
equipment.
1
B
Ch a rg in g t im e
The following table shows the charging time for the battery pack which is
discharged completely.
C
1
2
3
Set the mode change sw itch to VCR/CAMERA.
Connect the DC cord to the cigarette lighter socket.
Battery pack
Charging time Battery pack
Charging time
(M series))
Connect the connecting cord A to the DC OUT connector of this
(“InfoLITHIUM
NP-F550
”
(L series))
(“InfoLITHIUM
NP-FM50
NP-FM70
NP-FM90
”
unit.
– Reorient or relocate the receiving antenna.
115 (55)
170 (110)
225 (165)
105 (45)
150 (90)
195 (135)
4
Connect the connecting cord to the video equipment.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
NP-F750
Wh e n u sin g t h e co n n e ct in g co rd DK-415
(DCR-TRV9 e t c.) (ill.C-1)
While pressing the connecting plate B , slide it down.
To remove the connecting plate, slide it up while pressing the battery
release lever C.
NP-F950
– Consult the dealer or an experienced radio/ TV technician for help.
• Approximate minutes to charge an empty battery pack fully (Full charge).
• Approximate minutes in parentheses indicate the time when you charge
normally (Normal charge).
• To ascertain the battery life, refer to the instruction manual of the video
equipment which you use.
Wh e n u sin g t h e co n n e ct in g co rd DK-215
(DCR-TRV10 e t c.) (ill.C-2)
Open the cover, and insert the connecting plug D.
To remove the connecting plug, pull it out.
2
D
• The charging time may differ depending on the condition of the battery
pack or the temperature of the environment.
No t e s
No t e s
• When the mode change switch is set to VCR/ CAMERA during charging,
charging stops.
• If you set the mode change switch to CHARGE while operating the video
equipment, the power supply to the video equipment stops.
• You cannot charge the battery pack attached to this unit while supplying
the power to the video equipment.
• If the CHARGE lamp does not light or flash, check that the battery pack is
correctly attached to the DC adaptor/ charger. If it is not attached, it will
not be charged.
• Keep this unit away from the video equipment if the picture is disturbed.
|